30644 shaares
195 résultats
taggé
RaspberryPi
12MP Sony IMX708 back-illuminated and stacked CMOS image sensor
Sensor size – 7.4mm diagonal
Pixel size: 1.4μm x 1.4μm
Resolution – 4608 x 2592 pixels
FoV – See comparison table between different models below
Common video modes: 1080p50, 720p100, 480p120
Autofocus system: Phase Detection Autofocus; focus range (see table below)
IR cut filter – Integrated in standard variants; not present in NoIR variants
HDR mode up to 3 MP
Output: RAW10
Host interfaces via 15-pin FPC connector
CSI-2 serial data output
2-wire serial communication (supports I2C fast mode and fast-mode plus)
2-wire serial control of focus mechanism
Dimensions – 25 x 24 x 11.5mm (12.4mm height for the Wide variants)
https://www.tomshardware.com/reviews/raspberry-pi-camera-module-v3
Sensor size – 7.4mm diagonal
Pixel size: 1.4μm x 1.4μm
Resolution – 4608 x 2592 pixels
FoV – See comparison table between different models below
Common video modes: 1080p50, 720p100, 480p120
Autofocus system: Phase Detection Autofocus; focus range (see table below)
IR cut filter – Integrated in standard variants; not present in NoIR variants
HDR mode up to 3 MP
Output: RAW10
Host interfaces via 15-pin FPC connector
CSI-2 serial data output
2-wire serial communication (supports I2C fast mode and fast-mode plus)
2-wire serial control of focus mechanism
Dimensions – 25 x 24 x 11.5mm (12.4mm height for the Wide variants)
https://www.tomshardware.com/reviews/raspberry-pi-camera-module-v3
Ceux qui ont la chance de posséder les Compute Modules correspondants
ont ainsi accès simultanément à
six CPU Broadcom de type BCM2711 (Au total, 24 cœurs Cortex-A72 )
et jusqu’à 48 Go de RAM.
Les six slots pour cartes micro-SD et les slots M.2 se trouvent à l’arrière.
Comme DeskPi utilise les dimensions et les trous standard des cartes mères Mini-ITX,
le Super6C s’adapte à tous les boîtiers de PC possibles. Avec neuf connexions de ventilateur (trois fois 12 volts, six fois 5 volts), on peut faire fonctionner une mini-turbine si on le souhaite.
Une carte mère à 250 € (sans les CM4)
SoM – 6x sockets for up Raspberry Pi Compute Module 4
Storage
6x M.2 PCIe Gen2 x1 2280 sockets, one per CM4 module
6x MicroSD card slots, one per CM4 module
Video Output – 1x HDMI 2.0 output, 1x HDMI 1.4a output, both attached to the first Raspberry Pi CM4 module
Networking
2x Gigabit Ethernet RJ45 ports
Gigabit Ethernet switch to interconnect all 6x system-on-modules
USB
6x micro USB ports, one per CM4 module to flash the OS to the eMMC flash (except for Raspberry Pi CM4 Lite modules)
2x USB 2.0 Type-A ports, 2x USB 2.0 interfaces via header, all attached to the first CM4 module
Misc
Onboard ON/OFF and Reset button
PC Case front panel header
3x 12V fan headers
6x 5V fan header, one per CM6 module
Some LEDs
Power Supply – 19V to 24V DC via a power barrel jack or 12V via a 4-pin ATX connector
Dimensions – 170 x 170 x 21 mm (Mini-ITX form factor)
ont ainsi accès simultanément à
six CPU Broadcom de type BCM2711 (Au total, 24 cœurs Cortex-A72 )
et jusqu’à 48 Go de RAM.
Les six slots pour cartes micro-SD et les slots M.2 se trouvent à l’arrière.
Comme DeskPi utilise les dimensions et les trous standard des cartes mères Mini-ITX,
le Super6C s’adapte à tous les boîtiers de PC possibles. Avec neuf connexions de ventilateur (trois fois 12 volts, six fois 5 volts), on peut faire fonctionner une mini-turbine si on le souhaite.
Une carte mère à 250 € (sans les CM4)
SoM – 6x sockets for up Raspberry Pi Compute Module 4
Storage
6x M.2 PCIe Gen2 x1 2280 sockets, one per CM4 module
6x MicroSD card slots, one per CM4 module
Video Output – 1x HDMI 2.0 output, 1x HDMI 1.4a output, both attached to the first Raspberry Pi CM4 module
Networking
2x Gigabit Ethernet RJ45 ports
Gigabit Ethernet switch to interconnect all 6x system-on-modules
USB
6x micro USB ports, one per CM4 module to flash the OS to the eMMC flash (except for Raspberry Pi CM4 Lite modules)
2x USB 2.0 Type-A ports, 2x USB 2.0 interfaces via header, all attached to the first CM4 module
Misc
Onboard ON/OFF and Reset button
PC Case front panel header
3x 12V fan headers
6x 5V fan header, one per CM6 module
Some LEDs
Power Supply – 19V to 24V DC via a power barrel jack or 12V via a 4-pin ATX connector
Dimensions – 170 x 170 x 21 mm (Mini-ITX form factor)
MCU – Raspberry Pi RP2040 dual-core Cortex-M0+ microcontroller @ 133 MHz with 264KB SRAM
Storage – 2MB QSPI flash
Connectivity – 802.11b/g/n WiFi 4 with ABRACON onboard antenna (Infineon CYW43439 connected over SPI)
USB – 1x Micro USB 1.1 port used for power and programming
Expansion
2x 20-pin 2.54mm pitch header and castellated holes with 26x GPIOs, 3x 12-bit ADC up to 500 Kbps, 2x UART, 2x I2C, 2x SPI, 16x PWM, 2 × programmable I/O (PIO) blocks with 8 state machines
3.3V I/O voltage
Debugging – 3-pin Arm Serial Wire Debug (SWD) port
Misc – BOOTSEL button, user LED (GP25. WL_GPIO0), RTC
Power Supply – 5V via Micro USB port or 1.8 to 5.5V DC via VSYS pin
Dimensions – 51 x 21mm
Temperature Range – -20°C to 70°C
https://www.nextinpact.com/lebrief/69536/voici-raspberry-pi-pico-w-a-6-dollars-avec-wi-fi-ainsi-que-pico-h-et-wh
6$
Storage – 2MB QSPI flash
Connectivity – 802.11b/g/n WiFi 4 with ABRACON onboard antenna (Infineon CYW43439 connected over SPI)
USB – 1x Micro USB 1.1 port used for power and programming
Expansion
2x 20-pin 2.54mm pitch header and castellated holes with 26x GPIOs, 3x 12-bit ADC up to 500 Kbps, 2x UART, 2x I2C, 2x SPI, 16x PWM, 2 × programmable I/O (PIO) blocks with 8 state machines
3.3V I/O voltage
Debugging – 3-pin Arm Serial Wire Debug (SWD) port
Misc – BOOTSEL button, user LED (GP25. WL_GPIO0), RTC
Power Supply – 5V via Micro USB port or 1.8 to 5.5V DC via VSYS pin
Dimensions – 51 x 21mm
Temperature Range – -20°C to 70°C
https://www.nextinpact.com/lebrief/69536/voici-raspberry-pi-pico-w-a-6-dollars-avec-wi-fi-ainsi-que-pico-h-et-wh
6$
https://www.servethehome.com/getting-started-with-vmware-esxi-on-arm-with-a-raspberry-pi/
https://www.mchelgham.com/esxionarm-guide-dinstallation-vsphere-7-sur-raspberry-pi-4/
du délire je savais même pas que c'était possible !
https://www.mchelgham.com/esxionarm-guide-dinstallation-vsphere-7-sur-raspberry-pi-4/
du délire je savais même pas que c'était possible !
excellent !
Cet outil vous permettra de créer un cluster Proxmox composé de Raspberry Pi ou d’un cluster hybride Raspberry Pi + machines x86.
Cet outil vous permettra de créer un cluster Proxmox composé de Raspberry Pi ou d’un cluster hybride Raspberry Pi + machines x86.
ça parait presque trop beau
4 ports Gigabit, 4 USB 4.0, 2 ports HDMI 2.0,
un port série RS-485 : de quoi ravir les bidouilleurs,
par exemple pour un NAS avec les 5 ports SATA disponibles.
Rajoutez une alimentation ATX à 24 broches, tout ce qu’il y a de plus standard
et une batterie CR2032 pour alimenter le module RTC servant à conserver l’heure - un manque cruel du Pi,
(....)
Notez cependant la cruelle absence du GPIO, bien que deux ports FFC à 40 broches soient présents pour « une utilisation future », bien entendu non précisée.
4 ports Gigabit, 4 USB 4.0, 2 ports HDMI 2.0,
un port série RS-485 : de quoi ravir les bidouilleurs,
par exemple pour un NAS avec les 5 ports SATA disponibles.
Rajoutez une alimentation ATX à 24 broches, tout ce qu’il y a de plus standard
et une batterie CR2032 pour alimenter le module RTC servant à conserver l’heure - un manque cruel du Pi,
(....)
Notez cependant la cruelle absence du GPIO, bien que deux ports FFC à 40 broches soient présents pour « une utilisation future », bien entendu non précisée.
mouai
SiP – Raspberry Pi RP3A0 system-in-package with:
SoC – Broadcom BCM2710A1 quad-core Arm Cortex-A53 @ 1GHz (overclockable to 1.2 GHz) with VideoCore IV CPU supporting OpenGL ES 1.1, 2.0 graphics
Memory – 512MB LPDDR2
Storage – MicroSD card socket
Video output – Mini HDMI port, composite video via header
Camera – MIPI CSI-2 camera connector
Video
Decoding – H.264 and MPEG-4 up to 1080p30
Encoding – H.264 up to 1080p30
Connectivity – 2.4GHz IEEE 802.11b/g/n Wi-Fi 4 and Bluetooth 4.2 BLE with onboard antenna
USB – 1x Micro USB 2.0 OTG port
Expansion – Unpopulated 40-pin HAT-compatible I/O header
Power Supply – 5V/2.5A via Micro USB port
Dimensions – 65 x 30 mm (same form factor as previous Raspberry Pi Zero boards)
Temperature Range – -20°C to +70°C
Production lifetime – At least until January 2028
https://www.cnx-software.com/2021/10/28/raspberry-pi-zero-2-w-launched-with-quad-core-cpu-512mb-ram/
SoC – Broadcom BCM2710A1 quad-core Arm Cortex-A53 @ 1GHz (overclockable to 1.2 GHz) with VideoCore IV CPU supporting OpenGL ES 1.1, 2.0 graphics
Memory – 512MB LPDDR2
Storage – MicroSD card socket
Video output – Mini HDMI port, composite video via header
Camera – MIPI CSI-2 camera connector
Video
Decoding – H.264 and MPEG-4 up to 1080p30
Encoding – H.264 up to 1080p30
Connectivity – 2.4GHz IEEE 802.11b/g/n Wi-Fi 4 and Bluetooth 4.2 BLE with onboard antenna
USB – 1x Micro USB 2.0 OTG port
Expansion – Unpopulated 40-pin HAT-compatible I/O header
Power Supply – 5V/2.5A via Micro USB port
Dimensions – 65 x 30 mm (same form factor as previous Raspberry Pi Zero boards)
Temperature Range – -20°C to +70°C
Production lifetime – At least until January 2028
https://www.cnx-software.com/2021/10/28/raspberry-pi-zero-2-w-launched-with-quad-core-cpu-512mb-ram/
Raspberry Pi Compute Module 4 socket
Storage
NVMe SSD via M.2 2242 Key B socket (See Expansion section)
MicroSD card slot
Video Output
HDMI 2.0 port up to 4Kp60
MIPI DSI connector for Raspberry Pi LCD display
Camera – 1x MIPI CSI connector for Raspberry Pi camera
Connectivity
Gigabit Ethernet port with PoE
Optional WiFI 5 and Bluetooth 5.0 on Raspberry Pi CM4 module
Optional 3G/4G LTE (USB) modem via M.2 2242 Key B socket (See Expansion section)
USB – 3x USB 2.0 Type-A ports, 1x USB-C OTG port
Expansion
40-pin Raspberry Pi GPIO header
M.2 2242 Key B socket with micro-SIM cardholder
Misc – LEDs, , boot selection,
Power Supply
7.5 to 28V via 5.5/2.1mm power barrel jack or 2-pin 3.5mm terminal block.
5V via USB-C port, but not sufficient for M.2 cards
3-pin Input voltage breakout header designed to power HAT or other expansion boards
Circuit protections added for safety reasons (ESD, over-and reverse-current protections) including 5V/3.5A fuse
Dimensions – 9×9 cm and M3 mounting holes
100$
fabriqué par Oratek (pas par la fondation)
https://www.minimachines.net/actu/oratek-tofu-97646
Storage
NVMe SSD via M.2 2242 Key B socket (See Expansion section)
MicroSD card slot
Video Output
HDMI 2.0 port up to 4Kp60
MIPI DSI connector for Raspberry Pi LCD display
Camera – 1x MIPI CSI connector for Raspberry Pi camera
Connectivity
Gigabit Ethernet port with PoE
Optional WiFI 5 and Bluetooth 5.0 on Raspberry Pi CM4 module
Optional 3G/4G LTE (USB) modem via M.2 2242 Key B socket (See Expansion section)
USB – 3x USB 2.0 Type-A ports, 1x USB-C OTG port
Expansion
40-pin Raspberry Pi GPIO header
M.2 2242 Key B socket with micro-SIM cardholder
Misc – LEDs, , boot selection,
Power Supply
7.5 to 28V via 5.5/2.1mm power barrel jack or 2-pin 3.5mm terminal block.
5V via USB-C port, but not sufficient for M.2 cards
3-pin Input voltage breakout header designed to power HAT or other expansion boards
Circuit protections added for safety reasons (ESD, over-and reverse-current protections) including 5V/3.5A fuse
Dimensions – 9×9 cm and M3 mounting holes
100$
fabriqué par Oratek (pas par la fondation)
https://www.minimachines.net/actu/oratek-tofu-97646